Welding and hot work in Germany: hazards, hot work permit, fire watch and medical care
Welding fume, UV radiation, flying sparks: welding, flame cutting and abrasive cutting combine several hazards at once. Which rules apply after the withdrawal of chapter 2.26 of DGUV Rule 100-500, when a hot work permit is needed and when medical care becomes mandatory.
Last updated on 10 min readAMS Go editorial team
Key points at a glance
- Welding, cutting, soldering, brazing and abrasive cutting involve hazardous substances, optical radiation, fire and explosion hazards and electrical hazards; all of them belong in the risk assessment.
- For welding fume, TRGS 528 (the Technical Rule for Hazardous Substances on welding work) applies: first low-emission processes and materials, then extraction at source and ventilation, then organisational measures, and finally respiratory protection. Extraction equipment is inspected at least annually.
- Chapter 2.26 “Schweißen, Schneiden und verwandte Verfahren” of DGUV Rule 100-500 was withdrawn with the version of November 2024. The content can be found, among others, in TRGS 528, TRGS 555, DGUV Rule 113-004 and DGUV Information 209-010.
- Outside workplaces set up for the purpose, a written hot work permit (Schweißerlaubnis) with defined safety measures, a fire watch during the work and checks afterwards are needed where there is a fire or explosion hazard.
- Occupational medical care is mandatory if an air concentration of 3 mg/m³ of welding fume is exceeded; if it is complied with, medical care must be offered (ArbMedVV).
Which hazards come together in welding
Hot work (Heißarbeiten, also called Feuerarbeiten) includes welding, cutting, soldering and brazing, thawing and abrasive cutting as well as the heating of substances. Hardly any other activity combines so many hazards at one workplace. The duty to carry out a risk assessment follows from Section 5 of the Occupational Safety and Health Act (ArbSchG); depending on the hazard, the Hazardous Substances Ordinance (GefStoffV), the Ordinance on Artificial Optical Radiation (OStrV) and the Industrial Safety Ordinance (BetrSichV) also apply.
Welding fume and gases
Caused byRespirable particles, depending on material and process containing manganese, chromium(VI) or nickel compounds; plus ozone, carbon monoxide and nitrous gases
Relevant ruleHazardous Substances Ordinance, TRGS 528
Optical radiation
Caused byUV and infrared radiation and glare from arc and flame: arc eye, skin burns
Relevant ruleOStrV, DGUV Information 209-010
Fire and explosion
Caused byFlying sparks, weld spatter, heat conduction, smouldering spots that ignite only hours later; residues of flammable substances in containers and pipes
Relevant ruleHazardous Substances Ordinance Annex I no. 1, ASR A2.2, DGUV Information 205-001 and 209-010
Electrical hazard
Caused byWelding current, damaged cables, work in confined spaces or in wet conditions
Relevant ruleDGUV Regulation 3, DGUV Information 209-010
Oxygen deficiency and gas accumulation
Caused byShielding gases such as argon or carbon dioxide in containers, pits and confined spaces
Relevant ruleDGUV Rule 113-004
Burns, noise, awkward postures
Caused byHot workpieces, spatter and slag; noise from grinding and plasma cutting
Relevant rulePPE Use Ordinance, Noise and Vibration Occupational Safety Ordinance
Which rules apply after the withdrawal of chapter 2.26
Many operating instructions and training documents still refer to chapter 2.26 “Schweißen, Schneiden und verwandte Verfahren” (welding, cutting and allied processes) of DGUV Rule 100-500, which went back to the former accident prevention regulation VBG 15. With the updated version of DGUV Rule 100-500 of November 2024, this chapter was withdrawn. The DGUV explains this by saying that the content worth keeping is sufficiently covered in other publications. Today you rely on these sources:
- Hazardous Substances Ordinance and TRGS 528 “Schweißtechnische Arbeiten” (issued February 2020): risk assessment and protective measures against welding fume and gases. Anyone who complies with the TRGS can assume that the requirements of the ordinance are met in this respect.
- TRGS 555 on operating instructions and information for employees: operating instructions and safety instruction for activities involving hazardous substances.
- Ordinance on Artificial Optical Radiation (OStrV): assessment of radiation from arc and flame and protective measures.
- Hazardous Substances Ordinance Annex I no. 1: fire and explosion protection, including a permit-to-work system for particularly hazardous activities.
- ASR A2.2 “Maßnahmen gegen Brände” (measures against fires): fire extinguishing equipment and measures where the fire hazard is increased.
- DGUV Information 209-010 “Lichtbogenschweißen” (arc welding) and DGUV Information 209-011 “Gasschweißen” (gas welding): practical guidance on processes, protective equipment, electrical safety and fire protection.
- DGUV Information 205-001 on fire protection in practice: hot work, permit, fire watch and follow-up checks.
- DGUV Rule 113-004 on containers, silos and confined spaces: welding in confined spaces.
Welding fume under TRGS 528: emission groups and measures
According to TRGS 528, more than 95 % of welding fume generally comes from the filler material. The particles are mostly smaller than one micrometre and reach the alveoli. When welding high-alloy steels and nickel-based alloys, carcinogenic chromium(VI) compounds and nickel oxides can form. How much fume is released depends on the process. The TRGS therefore divides the processes into four emission groups:
low
Emission ratebelow 1 mg/s
ExamplesSubmerged arc welding, gas welding, TIG welding, soft soldering
medium
Emission rate1 to 2 mg/s
ExamplesLaser beam welding without filler material
high
Emission rate2 to 25 mg/s
ExamplesMAG welding with solid wire, manual metal arc welding, laser beam welding with filler material
very high
Emission rateabove 25 mg/s
ExamplesMAG welding with flux-cored wire without shielding gas, oxy-fuel cutting, plasma cutting, arc and flame spraying
The higher the emission group, the higher the requirements. For the groups “low” and “medium”, at least effective extraction at source is generally required; for “high” and “very high”, additional protective measures for welders and other employees in the danger area are generally required. The measures are to be considered in this order:
- 1
Check substitution
Select low-emission processes, materials and filler materials, for example a process with a lower emission rate or optimised process parameters.
- 2
Ventilation and structural measures
Extract the hazardous substances primarily at source, for example with on-torch extraction or with movable capture elements. The closer to the point of origin, the more effective. Separate welding areas physically; technical room ventilation is added where necessary.
- 3
Organisational and hygiene measures
Remove residues such as cold cleaners from the surface before welding, limit exposure times, position workpieces favourably, do not eat, drink or smoke at the workplace, store work clothing and street clothing separately.
- 4
Respiratory protection
If the other measures are not sufficient, the employer provides suitable respiratory protection, for example ventilated helmets or hoods with a blower and particle filter. For carcinogenic substances, the highest filter class P3 must generally be used.
- Effectiveness: capture and separation equipment must be effective; it must be checked for proper functioning at least annually by a person qualified to carry out inspections, and the inspection is documented.
- Assessment criteria: the measures must be designed so that at least the limit values are complied with, such as the general dust limit value of 1.25 mg/m³ for the respirable fraction. For carcinogenic substances, the graduated concept of measures in TRGS 910 also applies.
- Cleaning: dry sweeping and blowing off with compressed air are generally not permitted, not even for work clothing. Cleaning is done wet or with suitable industrial vacuum cleaners.
- Burdensome respiratory protection must not be a permanent measure. Blower-assisted welding helmets and hoods are regarded as non-burdensome and are therefore to be preferred.
- Grinding TIG electrodes produces dust that is harmful to health; suitable extraction is required here, especially for electrodes containing thorium dioxide.
Optical radiation and personal protective equipment
Arc and flame emit ultraviolet, visible and infrared radiation. Even a brief unprotected look into the arc can trigger a painful inflammation of the cornea and conjunctiva; unprotected skin burns as in sunburn. The hazard is assessed under the OStrV. Because the radiation cannot be avoided at the source, shielding and personal protective equipment are indispensable here:
Eyes and face
What mattersWelding shield or helmet with a welding filter in the shade number suited to the process and current; auto-darkening filters make work easier. Safety goggles or face protection when chipping slag and grinding.
Body
What mattersFlame-retardant welders' protective clothing to DIN EN ISO 11611 that leaves no skin exposed; no clothing soiled with oil or grease.
Hands
What mattersWelders' protective gloves to DIN EN 12477, dry and undamaged.
Feet
What mattersSafety footwear that protects against hot spatter and falling parts.
Airways
What mattersRespiratory protection according to the risk assessment, preferably blower-assisted welding helmets or hoods.
Hearing
What mattersHearing protection for noisy processes and ancillary work such as grinding and plasma cutting.
People nearby
What mattersWelding curtains, screens or booths; helpers also wear eye protection and suitable clothing.
The employer provides the protective equipment, takes care of maintenance and replacement and gives instruction in its use (PPE Use Ordinance). According to DGUV Information 205-001, welding and flame cutting may only be carried out by reliable persons over 18 who are familiar with the equipment and processes and have been instructed; younger persons only for training purposes under supervision.
Fire protection: hot work permit, fire watch and follow-up checks
Hot work outside workplaces set up for the purpose is particularly fire-prone, for example during assembly, repair and maintenance. Flammable materials are often not visible behind cladding, and smouldering spots sometimes ignite only hours after the work has ended. According to DGUV Information 205-001, the employer determines in the risk assessment whether written permission from company management or an authorised person is required for the planned work; without written permission, hot work may only take place at workplaces designated for it. DGUV Information 209-010 requires a permit, the Schweißerlaubnis, where there is a fire and explosion hazard outside such areas. The guide values in both publications show how far sparks travel:
Soldering and brazing with a flame
Horizontal rangeup to 2 m
Upwardsup to 2 m
Downwardsup to 10 m
Welding (manual gas and arc welding)
Horizontal rangeup to 7.5 m
Upwardsup to 4 m
Downwardsup to 20 m
Thermal cutting
Horizontal rangeup to 10 m
Upwardsup to 4 m
Downwardsup to 20 m
- 1
Check alternatives and inspect the work location
Can the work be done with a process without ignition hazard or in the workshop? If not: inspect the work area and its surroundings, including neighbouring rooms, floors below and cavities.
- 2
Remove, cover, seal
Remove flammable substances and objects from the danger area, including dust deposits and packaging. What has to stay is covered, for example with flame-retardant tarpaulins; openings, joints and penetrations to neighbouring areas are sealed.
- 3
Provide extinguishing agents, appoint a fire watch
Suitable fire extinguishers for the fire classes present are ready at the work location; the employees have been instructed in their use. During the work, the fire watch observes the endangered area, fights incipient fires and reports them.
- 4
Issue the permit in writing
The safety measures are set out in the permit and signed by company management or the authorised person, those carrying out the work and the fire watch. With contractors, the client and the contractor agree the measures.
- 5
Carry out the work
Only at the stated location and in the stated period. If conditions change, work is interrupted and reassessed.
- 6
Follow-up checks
After the work, the work location is checked regularly and the surroundings are examined for smouldering spots, suspicious heating and smoke until a fire developing can be ruled out. DGUV Information 205-001 gives a time window of two to four hours for this.
Occupational medical care, operating instructions and safety instruction
Which medical care is due depends on the exposure. The annex to the Ordinance on Occupational Medical Care (ArbMedVV) is decisive; TRGS 528 summarises the occasions for welding work:
Welding and cutting of metals where an air concentration of 3 mg/m³ of welding fume is exceeded
Type of medical careMandatory care (Pflichtvorsorge)
Reference in the annex to the ArbMedVVPart 1 (1) no. 2 (b)
Welding and cutting of metals where an air concentration of 3 mg/m³ of welding fume is complied with
Type of medical careOffered care (Angebotsvorsorge)
Reference in the annex to the ArbMedVVPart 1 (2) no. 2 (f)
Activities with category 1A or 1B carcinogens from Part 1 (1) no. 1, such as chromium(VI) compounds or nickel oxides, if repeated exposure cannot be ruled out
Type of medical careMandatory care, and follow-up care after the activity ends
Reference in the annex to the ArbMedVVPart 1 (1) no. 1 (b), (3) no. 1
Wearing respiratory protective devices of groups 2 and 3
Type of medical careMandatory care
Reference in the annex to the ArbMedVVPart 4 (1) no. 1
Wearing respiratory protective devices of group 1
Type of medical careOffered care
Reference in the annex to the ArbMedVVPart 4 (2) no. 2
Artificial optical radiation, if the exposure limit values are exceeded or may be exceeded respectively
Type of medical careMandatory care or offered care respectively
Reference in the annex to the ArbMedVVPart 3 (1) and (2)
According to TRGS 528, the threshold of 3 mg/m³ refers to the respirable dust fraction. For non-burdensome respiratory protection such as blower-assisted welding helmets, TRGS 528 states that the occasion for medical care on account of respiratory protection does not apply. In addition, every welding workplace needs operating instructions under Section 14 of the Hazardous Substances Ordinance and safety instruction before work starts and at least annually thereafter: on welding fume and extraction, protective equipment, fire protection, what to do in the event of fire and the permit procedure.
Checklist: organising welding and hot work safely
- Risk assessment prepared for all welding, cutting, soldering, brazing and abrasive cutting work, including welding fume, radiation, fire, electricity and confined spaces
- Processes and filler materials checked for lower-emission alternatives
- Extraction at source in place, effective and inspected at least annually
- Welding areas separated, welding curtains or screens in place to protect others
- Protective equipment defined, provided and in good condition: helmet with suitable filter, protective clothing, gloves, safety footwear, respiratory and hearing protection where needed
- Welding equipment, cables, hoses and safety devices visually checked before use and inspected regularly, gas cylinders secured against falling over
- Fixed welding workplaces free of flammable materials, fire extinguishers within reach
- Permit procedure introduced for hot work outside workplaces set up for the purpose, persons responsible for the release appointed
- Fire watch and follow-up checks regulated with duration and intervals, permits are kept
- Contractors integrated into the permit procedure, coordinator appointed where there is mutual endangerment
- Mandatory and offered medical care arranged and documented in the medical care register
- Operating instructions in place, employees instructed, references to withdrawn rules updated
Frequently asked questions
Does DGUV Rule 100-500 chapter 2.26 still apply?
No. Chapter 2.26 “Schweißen, Schneiden und verwandte Verfahren” was withdrawn with the updated version of DGUV Rule 100-500 of November 2024. According to the DGUV's note, the content worth keeping is contained in other publications, including TRGS 528, TRGS 555, DGUV Rule 113-004 and DGUV Information 209-010.
When do I need a hot work permit?
When hot work takes place outside workplaces set up for the purpose and a fire or explosion hazard cannot be ruled out. Whether written permission is necessary is determined by the employer in the risk assessment; according to DGUV Information 205-001, hot work without written permission may only be carried out at workplaces designated for it, such as the metalworking shop.
How long do checks have to continue after welding work?
There is no duration laid down by law. DGUV Information 205-001 refers to regular checks of the work location in a time window of two to four hours after the work, until a further fire developing can be ruled out. You define duration and intervals according to the risk assessment and enter them in the permit.
When is occupational medical care mandatory for welders?
Mandatory care must be arranged if an air concentration of 3 mg/m³ of welding fume is exceeded during welding and cutting of metals. If the value is complied with, the employer must offer medical care. Further occasions can be carcinogenic substances such as chromium(VI) compounds, wearing respiratory protection and optical radiation.
Is general hall ventilation enough against welding fume?
As a rule, no. TRGS 528 requires hazardous substances to be extracted primarily at source; for manual welding, capture at source is required in principle. Only in individual cases can the risk assessment show that natural room ventilation is sufficient, for example for processes in the “low” emission group or for work with low exposure.
This guide gives a general overview of German occupational safety law and does not replace legal advice. The regulations in force and the rules of the statutory accident insurance institutions are authoritative.
Organise occupational safety digitally
With the occupational safety software AMS Go you handle risk assessments, safety instructions, inspections and more in one system – mobile and with AI support.
Newsletter
Occupational safety, straight to your inbox
New templates, guides and changes to regulations – free from AMS Go. The newsletter is in German. You can unsubscribe at any time via the link in every email.
More guides
- Protective measures
Respiratory protection at work in Germany: selection, health checks and rules of use
8 minRead - Health
Occupational health checks in Germany: mandatory, offered and on request
8 minRead - Protective measures
Personal protective equipment (PPE): duties, selection and instruction
8 minRead - Organisation
Contractor management in Germany: coordinating, briefing and documenting contractors
8 minRead - Protective measures
Confined space work in Germany: hazards, entry permit and rescue
8 minRead - Fire safety
Fire extinguishers at work: calculating the number, inspection and mounting
8 minRead




