Cranes and slings in Germany: inspection, crane operators, slingers and discard criteria
How often does a crane have to be inspected, and by whom? Who may operate a crane, who may sling loads? And when must chains, ropes and webbing slings be discarded? The German duties relating to cranes, load-handling attachments and slings at a glance.
Last updated on 10 min readAMS Go editorial team
Key points at a glance
- Cranes are inspected at least annually by a person qualified to carry out inspections; tower cranes, mobile cranes, derrick cranes and truck-mounted cranes as well as large lorry loader cranes additionally at least every four years of operation by an inspection expert (Annex 3 section 1 of the Industrial Safety Ordinance, BetrSichV; Section 26 of DGUV Regulation 52).
- Stationary power-driven cranes such as overhead travelling cranes, gantry cranes and slewing jib cranes are inspected by an inspection expert before first being put into service, as are all cranes after modifications subject to inspection. The records are kept for the entire service life.
- Crane operators must be at least 18 years old, physically and mentally fit, instructed and appointed by the employer, and must have demonstrated their competence; for mobile power-driven cranes the appointment must be in writing (Section 29 of DGUV Regulation 52).
- Load-handling attachments and slings are inspected by a qualified person at intervals of no more than one year, and round steel chains additionally for cracks at intervals of no more than three years (DGUV Rule 109-017).
- Slings must be discarded, for example, if the marking is missing, a strand is broken, there are kinks, a chain link has elongated by more than 3 % or load-bearing seams are damaged.
Terms and rules at a glance
When loads are lifted, several components work together, and different inspection duties apply to them. DGUV Rule 109-017 on operating load-handling attachments and slings in lifting operations (issued December 2020) distinguishes:
Tragmittel (load-carrying means)
MeaningDevices permanently connected to the hoist for taking up load-handling attachments, slings or loads; they are inspected together with the crane
ExamplesHoist rope, the crane's load hook, permanently installed grabs, lifting beams and tongs
Lastaufnahmemittel (load-handling attachments)
MeaningDevices not belonging to the hoist that are connected to the load-carrying means in order to take up the load
ExamplesLifting beams, C-hooks, grabs, clamps, tongs, crane forks, lifting magnets, vacuum lifters
Anschlagmittel (slings)
MeaningDevices not belonging to the hoist that form the connection between the load-carrying means and the load or the load-handling attachment
ExamplesChain slings, wire rope slings, webbing slings, round slings, shackles
Anschlagpunkte (lifting points)
MeaningDetachable or fixed devices on the load by which it is lifted
ExamplesEye bolts, weld-on lifting eyes, swivel lifting points
- Industrial Safety Ordinance (Betriebssicherheitsverordnung, BetrSichV): inspection duties under Section 14, with fixed intervals and inspection responsibilities for cranes in Annex 3 section 1; requirements for lifting loads in Annex 1 no. 2.
- DGUV Regulation 52 “Krane” (cranes; DGUV Regulation 53 for the public-sector accident insurance institutions): inspections, inspection log, requirements for crane operators and operation.
- DGUV Rule 109-017: selection, use, inspection and discard criteria for load-handling attachments and slings, qualification of slingers.
- DGUV Principle 309-003 on the selection, instruction and proof of competence of crane operators and DGUV Information 209-013 “Anschläger” (slingers): aids for training and instruction.
Crane inspection: intervals and responsibilities
Annex 3 section 1 BetrSichV specifies for cranes who inspects before first use and who inspects periodically. Table 1 applies to power-driven cranes, Table 2 to manually operated and partly power-driven cranes:
Trolleys, jib and slewing cranes, overhead travelling cranes, wall-mounted travelling cranes, gantry cranes and slewing jib cranes
Inspection after assembly and before first being put into serviceInspection expert
Periodic inspectionAt least annually by a person qualified to carry out inspections
Tower cranes
Inspection after assembly and before first being put into servicePerson qualified to carry out inspections
Periodic inspectionAt least annually by a qualified person and at least every 4 years of operation, in the 14th and 16th year of operation and at least annually thereafter by an inspection expert
Mobile tower cranes (truck-mounted tower cranes)
Inspection after assembly and before first being put into serviceNot required
Periodic inspectionAt least every six months by a qualified person; inspection expert as for tower cranes
Mobile cranes and lorry loader cranes with a load moment of more than 300 kNm or a jib length of more than 15 m
Inspection after assembly and before first being put into serviceNot required
Periodic inspectionAt least annually by a qualified person and at least every 4 years of operation, in the 13th year of operation and at least annually thereafter by an inspection expert
Other lorry loader cranes, cable cranes
Inspection after assembly and before first being put into serviceNot required
Periodic inspectionAt least annually by a person qualified to carry out inspections
Truck-mounted cranes (Lkw-Anbaukrane), derrick cranes
Inspection after assembly and before first being put into serviceNot required
Periodic inspectionAt least annually by a qualified person and at least every 4 years of operation by an inspection expert
Manually operated or partly power-driven cranes with a load capacity of more than 1 t
Inspection after assembly and before first being put into serviceInspection expert
Periodic inspectionAt least annually by a person qualified to carry out inspections
Manually operated or partly power-driven cranes with a load capacity of up to 1 t
Inspection after assembly and before first being put into servicePerson qualified to carry out inspections
Periodic inspectionAt least annually by a person qualified to carry out inspections
- If a periodic inspection by an inspection expert is prescribed, a qualified person does not have to inspect additionally in the same year.
- After modifications subject to inspection, an inspection expert inspects; after exceptional events such as accidents or damage, a person qualified to carry out inspections.
- The interval is a maximum. Under Section 26 of DGUV Regulation 52, inspections take place as required, but at least annually: a crane in three-shift operation with high utilisation or in an aggressive atmosphere needs shorter intervals; the manufacturer's inspection instructions must be observed.
- Tower cranes are additionally inspected by a competent person each time they are erected and after each change of configuration (Section 26 (2) of DGUV Regulation 52).
- For cranes, due dates are given by month and year; a periodic inspection is deemed to be on time if it takes place no later than two months after the due date (Section 14 (5) BetrSichV).
- The records must be kept for the entire service life of the crane. Under Section 27 of DGUV Regulation 52, the results are entered in an inspection log; in it the employer confirms that they have taken note of the defects and that these have been remedied.
- If a defect gives rise to concerns about continued operation, the crane is taken out of service until the defect has been remedied and any necessary re-inspection has been carried out.
Who inspects: qualified person, competent person, inspection expert
The Industrial Safety Ordinance and DGUV Regulation 52 use different terms for the persons who inspect. In substance, the Sachkundiger and the qualified person, and the Sachverständiger and the inspection expert, largely correspond:
Person qualified to carry out inspections (zur Prüfung befähigte Person)
ReferenceSection 2 (6) BetrSichV, TRBS 1203
RequirementsVocational training, professional experience and recent professional activity that provide the knowledge required for the inspection
Competent person (Sachkundiger)
ReferenceImplementation instruction on Section 26 of DGUV Regulation 52
RequirementsTechnical training and experience, sufficient knowledge in the field of cranes and of the relevant regulations and rules, so that the safe condition can be assessed; for example plant engineers, crane foremen or specially trained specialist staff
Inspection expert (Prüfsachverständiger)
ReferenceAnnex 3 section 1 no. 2 BetrSichV
RequirementsQualified person who is additionally an engineer or has comparable knowledge, has at least three years' experience in the design, construction, maintenance or inspection of cranes, of which six months' involvement in the work of an inspection expert, and has the necessary equipment and documents
Expert (Sachverständiger)
ReferenceSection 28 of DGUV Regulation 52
RequirementsExperts of the technical inspection bodies and experts authorised by the accident insurance institution
The annual inspection can be carried out by one of your own specialists if they meet the requirements, are not subject to technical instructions during the inspection and are not disadvantaged because of their inspection work (Section 14 (6) BetrSichV). Many companies outsource it to the manufacturer or a crane service provider. Responsibility for ensuring that inspections take place and defects are remedied remains with the employer.
Inspection register in AMS GoRecord cranes, load-handling attachments and slings with inspection interval, type of inspection and internal or external inspector, file inspection reports with the equipment and get timely reminders of inspections that are due.Crane operators: requirements, appointment and duties
There is no statutory “crane licence” in Germany. Under Section 29 of DGUV Regulation 52, however, the employer may only employ persons to operate or maintain a crane independently if they meet four requirements, and must appoint them to their tasks. This does not apply to manually operated cranes.
- At least 18 years old (younger persons only for training, under the guidance and constant supervision of experienced persons)
- Physically and mentally fit
- Instructed in operating or maintaining the crane, competence demonstrated to the employer
- Can be expected to perform the assigned tasks reliably
- Appointed by the employer, in writing for mobile power-driven cranes
Besides theory, instruction includes sufficient practical operating experience and the ability to recognise defects that endanger safety. DGUV Principle 309-003 describes selection, instruction and proof of competence. The Industrial Safety Ordinance additionally requires that work equipment involving particular hazards is only used by appointed employees and that instruction is given at least once a year (Section 12 BetrSichV). In operation, the crane operator has, among others, these duties under Section 30 of DGUV Regulation 52:
- At the start of work, check the function of the brakes and emergency limit devices and watch the crane for obvious defects; with radio-controlled cranes, check that the control unit is assigned to the right crane.
- Stop crane operation if there are defects that endanger safety; report all defects to the supervisor and, at a change of operator, to the person taking over.
- Watch the load, or the load-handling device when travelling empty, during all movements; if this is not possible, operate only on the signals of a signaller.
- Loads should not be moved over persons. With load-handling attachments that hold the load only by magnetic, frictional or suction forces, this is prohibited.
- Move manually slung loads only on a clear signal from the slinger or signaller; do not move loads that have been slung improperly.
- Do not load the crane beyond the maximum permissible load (Section 31 of DGUV Regulation 52) and keep the controls within reach as long as a load is suspended from the crane.
- Do not operate outdoor cranes beyond the wind limits set by the manufacturer and secure them against wind at the end of work.
Slingers: slinging loads safely
The Industrial Safety Ordinance requires that loads are slung safely, that loads, load-handling attachments and slings cannot come loose or shift unintentionally, and that employees are not endangered by suspended loads (Annex 1 no. 2.5). According to DGUV Rule 109-017, only persons who are at least 18 years old, physically and mentally fit, qualified for the task and reliable, and who have demonstrated their competence, should be appointed to sling loads independently. The rule recommends making the appointment in writing. The slinging procedure:
- 1
Determine weight and centre of gravity
If the weight is not shown on the load or in the documents, it is weighed or calculated. The position of the centre of gravity must also be known before transport.
- 2
Select the sling
Use only marked equipment with sufficient load capacity, suited to the surface, shape, temperature and edges of the load. When slinging with several legs, as a rule only two may be assumed to be load-bearing; the angle of inclination must not exceed 60°.
- 3
Visual check before use
Equipment with obvious defects or malfunctions is not used. If there are doubts about its safe condition, the equipment is withdrawn from use.
- 4
Sling properly
Do not hook load hooks directly into the load unless it has an attachment device designed for this. Use hooks with a safeguard against unintentional unhooking, protect sharp edges, and do not carry loose parts on the load.
- 5
Leave the danger area and give signals
Before lifting, everyone leaves the danger area. Communication with the crane operator is agreed beforehand; if several people sling the load, only one responsible person gives the signals.
- 6
Set down and unhook
The load is only unhooked once it has been set down in a stable position. Afterwards store slings protected, not lying on the floor.
Inspection and discard criteria for slings
The employer defines the type, scope and intervals of inspections in the risk assessment (Section 3 (6) BetrSichV). DGUV Rule 109-017 gives proven intervals for this: load-handling attachments and slings are inspected by a person qualified to carry out inspections at intervals of no more than one year, more often with frequent use, increased wear, corrosion or exposure to heat. Round steel chains are additionally subjected to non-destructive crack testing at intervals of no more than three years, and webbing slings with a vulcanised-on cover are tested for wire breaks and corrosion at intervals of no more than three years. After damage and repairs, an extraordinary inspection is due. The result is recorded and kept at least until the next inspection. During the visual inspection, the qualified person pays particular attention to these defects:
All
What to look out for in particular during the inspectionMissing, damaged or illegible marking; fractures, deformation, incipient cracks; heavy wear; corrosion damage; missing components; malfunctions of safety devices
Chain slings
What to look out for in particular during the inspectionDeformation or fracture of a chain link; incipient cracks, notches, corrosion pits; discolouration due to heat; reduction of the averaged link thickness by more than 10 % of the nominal thickness; elongation of the outer nominal dimension of a chain link by more than 3 %
Steel wire rope slings
What to look out for in particular during the inspectionKinks; fracture of a strand; crushing; loosening of the outer layer; corrosion; damaged rope termination; for stranded ropes 6 visible wire breaks over a length of 6 rope diameters, 14 over 30 rope diameters or 3 adjacent wire breaks in one strand
Webbing slings and round slings made of man-made fibres
What to look out for in particular during the inspectionYarn breaks, abrasion and other mechanical damage according to the manufacturer's information; transverse or longitudinal cuts, damage to the selvedges; damaged load-bearing seams; damaged sleeve on round slings; damage due to heat or aggressive substances
Fibre ropes
What to look out for in particular during the inspectionFracture of a strand; yarn breaks, cuts, loosening; damage due to heat, damp storage or aggressive substances; loosened splices
Load hooks
What to look out for in particular during the inspectionCracks and corrosion; opening of the hook mouth by more than 10 % or twisting; wear in the hook saddle of more than 5 % of the web height; missing or defective safety latch
The wire break numbers are outermost limits; discarding earlier serves safety. If safety-relevant defects are found, the equipment must not be used further until they have been remedied. Slings that have reached discard criteria are taken out of circulation immediately and rendered unusable so that they do not accidentally end up on the hook again. Repairs may only be carried out by persons with the necessary knowledge in accordance with the manufacturer's specifications.
Checklist: cranes and slings in the company
- All cranes, load-handling attachments and slings recorded in a register, with marking, load capacity and location
- For each crane, crane type, inspection intervals and inspection responsibility defined in line with Annex 3 BetrSichV, due date recorded by month and year
- Inspection before first being put into service and after modifications subject to inspection arranged with inspection experts
- Inspection log for each crane in place, inspection results entered, remedying of defects confirmed
- Crane operators selected, instructed, competence demonstrated, appointed, in writing for mobile power-driven cranes
- Slingers qualified and appointed, hand signals or radio communication defined
- Operating instructions for crane operation in place, annual instruction documented
- Daily function check of brakes and emergency limit devices by the crane operator regulated
- Slings inspected at intervals of no more than one year, crack testing of round steel chains at intervals of no more than three years
- Load tables available at the point of use, edge protection available, storage dry and orderly
- Slings that have reached discard criteria are sorted out and rendered unusable
Frequently asked questions
How often does a crane have to be inspected?
At least annually by a person qualified to carry out inspections, mobile tower cranes at least every six months (Annex 3 section 1 BetrSichV). Tower cranes, mobile cranes, derrick cranes and truck-mounted cranes as well as large lorry loader cranes are additionally inspected by an inspection expert at least every four years of operation. High utilisation or an aggressive environment may require shorter intervals.
Who may inspect a crane?
The annual inspection is carried out by a person qualified to carry out inspections, called Sachkundiger in DGUV Regulation 52. This can also be one of your own specialists if they have the necessary knowledge through training, experience and recent activity. Inspections before many cranes are first put into service, after modifications subject to inspection, and the inspections at four-year intervals are reserved for inspection experts.
Do you need a crane licence?
There is no official crane operator's licence. However, anyone who independently operates a power-driven crane must be at least 18 years old, fit, instructed and appointed by the employer and must have demonstrated their competence (Section 29 of DGUV Regulation 52). DGUV Principle 309-003 describes what selection, instruction and proof of competence can look like. For mobile power-driven cranes, the appointment must be made in writing.
How often do slings have to be inspected?
According to DGUV Rule 109-017, at intervals of no more than one year by a person qualified to carry out inspections, more often under heavy use. Round steel chains additionally need non-destructive crack testing at intervals of no more than three years. Before each use, the slinger checks the equipment for obvious defects.
How long do inspection records have to be kept?
For cranes, for the entire service life (Annex 3 section 1 no. 3.3 BetrSichV). For load-handling attachments and slings, at least until the next inspection (Section 14 (7) BetrSichV, DGUV Rule 109-017). It makes sense to keep the records for slings longer as well, in order to be able to trace the progression of wear.
This guide gives a general overview of German occupational safety law and does not replace legal advice. The regulations in force and the rules of the statutory accident insurance institutions are authoritative.
Organise occupational safety digitally
With the occupational safety software AMS Go you handle risk assessments, safety instructions, inspections and more in one system – mobile and with AI support.
Newsletter
Occupational safety, straight to your inbox
New templates, guides and changes to regulations – free from AMS Go. The newsletter is in German. You can unsubscribe at any time via the link in every email.
More guides
- Testing duties
UVV inspections in Germany: what must be inspected, how often and by whom
8 minRead - Testing duties
Inspection intervals table: German inspection deadlines for work equipment and installations
9 minRead - Inspections
Inspection intervals for work equipment in Germany: overview, duties and records
8 minRead - Testing duties
Qualified person for inspections under TRBS 1203 in Germany: requirements, duties and appointment
6 minRead - Safety instruction
Forklift licence in Germany: training, authorisation and annual instruction for drivers
7 minRead - Safety instruction
Mobile elevating work platforms in Germany: training, authorisation and inspection
6 minRead




