Slips, trips and falls in Germany: causes, rules and measures
Almost a quarter of all reportable accidents at work in Germany are slips, trips and falls. What counts as a tripping hazard, which slip resistance a floor needs, when stairs must have a handrail and which measures really help.
Last updated on 9 min readAMS Go editorial team
Key points at a glance
- In 2025 the German Social Accident Insurance (DGUV) counted 157,095 reportable slip, trip and fall accidents (Stolper-, Rutsch- und Sturzunfälle, SRS) at work – almost a quarter of the 664,862 reportable occupational accidents. 2,260 of them led to a new accident pension.
- Floors must have no unevenness, holes, tripping hazards or dangerous slopes and must be load-bearing, safe to walk on and slip-resistant (Annex no. 1.5 of the Workplaces Ordinance, ArbStättV). The details are set out in ASR A1.5 “Fußböden” (floors).
- In rooms, under level conditions, a height difference of more than 4 mm already counts as a tripping hazard. The required slip resistance is given in R groups from R 9 to R 13.
- Stairs need a handrail, on both sides from a step width of 1.5 m; traffic routes must be clear, lit and cleared or gritted in winter (ASR A1.8).
- Measures follow the TOP principle: first suitable floors and structural solutions, then cleaning, order and inspections, and finally footwear and behaviour.
Slips, trips and falls in figures: underestimated and costly
Tripping, slipping and falling sounds harmless but is one of the largest blocks in accident statistics. The DGUV statistics “Arbeitsunfallgeschehen 2025” group under this heading accidents while walking that are triggered by tripping, slipping, twisting an ankle or falling over. Falls from height are counted separately.
Reportable occupational accidents at work in total
Value664,862
Of which slips, trips and falls
Value157,095, i.e. almost 24 %
New accident pensions after slips, trips and falls
Value2,260 of a total of 8,442
Slips, trips and falls on floors, surfaces and in traffic areas
Value80,838 (51.5 %)
Slips, trips and falls on stairs
Value29,674 (18.9 %)
Floor slippery due to water, rain, snow or ice
Value12,934
Floor slippery due to oil, grease and the like
Value4,026
The typical consequences are injuries to the ankle and foot (39 %) and to the knee and lower leg (21 %), mostly strains, sprains and bruises. In the cases that lead to an accident pension, fractures dominate at 69 %. According to the DGUV, those affected are unable to work for a median of twelve days after a slip, trip or fall. A third of the accidents occur in industrial and commercial settings, i.e. in production, workshops and at loading and unloading points, and a good fifth in office and service settings.
What the Workplaces Ordinance and the ASR require
The basic requirement is in the annex to the Workplaces Ordinance, the details in the Technical Rules for Workplaces (Technische Regeln für Arbeitsstätten, ASR). The rules on floors and traffic routes were reissued in March 2022 and have been amended since; older overviews often still cite earlier versions.
Annex no. 1.5 (2) ArbStättV
Status–
ContentFloors must have no unevenness, holes, tripping hazards or dangerous slopes; they must be secured against shifting, load-bearing, safe to walk on and slip-resistant
Annex no. 1.8 ArbStättV
Status–
ContentTraffic routes including stairs must be laid out and dimensioned so that they can be walked or driven on easily and safely
ASR A1.5 “Fußböden” (floors)
StatusIssued March 2022, last amended May 2025
ContentTripping hazards, slip resistance with R groups and displacement space, cleaning, thermal insulation, slip resistance requirements by work area (Annex 2)
ASR A1.8 “Verkehrswege” (traffic routes)
StatusIssued March 2022, last amended June 2024
ContentWidths of traffic routes, stairs, handrails, fixed ladders, loading ramps, operation and maintenance
ASR A5.1 on workplaces in premises not enclosed on all sides and outdoor workplaces
StatusIssued August 2025
ContentMeasures against slipping hazards from rain, snow and ice
ASR A3.4 “Beleuchtung und Sichtverbindung” (lighting and view to the outside)
StatusIssued May 2023
ContentMinimum illuminance values, such as 50 lux in corridors and 100 lux on stairs
The annexes of ASR A1.5 on testing and assigning slip resistance are based on DGUV Rule 108-003 on floors in work rooms and work areas with a risk of slipping. In general, ASR A1.5 requires floors to be designed, maintained and cleaned so that they can be used safely. Regular inspections are to ensure that defects are detected promptly even in rarely used areas; defects found must be remedied without delay.
Tripping hazards: what counts and how to remove them
ASR A1.5 describes tripping hazards as changes in the surface in areas that are walked on which increase the risk of falling, and gives concrete dimensions:
- Height differences of more than 4 mm already count as a tripping hazard under level conditions in rooms.
- Gaps in the floor more than 20 mm wide and gratings with a mesh size of more than 35 × 51 mm are also tripping hazards.
- Height differences of up to 2 cm can be defused by a bevel of no more than 25°, for example at the edges of floor coverings. Larger height differences should be bridged by walkable ramps.
- Strips, covers, drainage channels and profiles must be laid so that they cannot tip and are safe to step on, flush and level with the floor, and firmly anchored.
- Connection and supply lines must not form tripping hazards: lay them outside traffic routes and work areas or provide enough connections close to the equipment.
- Mats and other overlays count as part of the floor. They must be secured against shifting and must not themselves form a tripping hazard.
Slip resistance: the R groups R 9 to R 13
Slipping hazards are to be avoided primarily through suitable floors and floor coverings. The yardstick is the R group: a test person walks on the covering, coated with a lubricant, on an inclined plane whose slope is increased until they can no longer walk safely. The mean angle determines the R group. Annex 2 of ASR A1.5 assigns a minimum R group to work areas in which slip-promoting substances get onto the floor:
R 9
Angle of slip6° to 10°
Examples from Annex 2 of ASR A1.5Entrance areas indoors, stairs indoors, toilet rooms, break rooms, first-aid rooms, sales and customer rooms
R 10
Angle of slipmore than 10° to 19°
Examples from Annex 2 of ASR A1.5Changing rooms and washrooms, garages not exposed to the weather
R 11
Angle of slipmore than 19° to 27°
Examples from Annex 2 of ASR A1.5Repair and maintenance rooms in motor vehicle workshops, kitchens for communal catering in homes and schools; outdoors, footpaths, outdoor stairs and entrance areas (R 11 or R 10 with displacement space V 4)
R 12
Angle of slipmore than 27° to 35°
Examples from Annex 2 of ASR A1.5Restaurant and hotel kitchens, working and inspection pits in motor vehicle workshops (with V 4), uncovered loading ramps (R 12 or R 11 with V 4)
R 13
Angle of slipmore than 35°
Examples from Annex 2 of ASR A1.5Areas with heavy grease loads, such as fat rendering
- Displacement space: profiled coverings take up slip-promoting substances below the walking surface. The code V 4 to V 10 gives the minimum volume in cm³ per dm².
- Transitions: adjoining floors that are walked on continuously should differ by no more than one R group, or by no more than two if the transition is clearly recognisable or to be expected, for example at a door.
- Building entrances: entrance matting zones should be at least 1.5 m long in the walking direction across the full width of the passage, be secured against shifting and be cleaned or replaced in good time.
- Cleaning: choose cleaning methods and agents so that the floor still has the required slip resistance afterwards. Contamination that can lead to hazards must be removed without delay.
- Wet cleaning: where possible at times when the area is not in use. Otherwise the area is cordoned off until dry or at least marked; warning signs placed on the floor have proved effective.
- Draining liquids: surfaces next to drains and channels should have a gradient of at least 2 %; where possible, do not drain liquids across traffic routes.
Stairs and traffic routes under ASR A1.8
Almost one in five slips, trips and falls happens on stairs. ASR A1.8 requires that stairs can be used safely and easily, with sufficiently large, level, slip-resistant, recognisable and load-bearing treads at even intervals:
Handrail
Requirement of ASR A1.8Every staircase must have a handrail; handrails on both sides where the step width is more than 1.5 m, plus intermediate handrails where the distance between handrails is more than 4.0 m
Handrail in existing buildings
Requirement of ASR A1.8In workplaces built or applied for by 30 June 2013, at least one handrail is needed on stairs with more than 4 steps, unless building regulations require more
Height of the handrail
Requirement of ASR A1.8Between 0.80 m and 1.15 m; diameter or width between 2.5 cm and 6 cm
Rise and going
Requirement of ASR A1.8Rise 14 to 19 cm, going 26 to 32 cm; step measure (twice the rise plus the going) between 59 and 65 cm. A rise of 17 cm and a going of 29 cm are considered particularly safe
Intermediate landing
Requirement of ASR A1.8After no more than 18 steps at a pitch of up to 36°
Guard rail
Requirement of ASR A1.8At least 1.00 m high on open sides, at least 1.10 m where the fall height is more than 12 m
Steps
Requirement of ASR A1.8Treads slip-resistant, no tripping hazards such as protruding edge profiles, steps lit with good contrast
- Width: pedestrian routes must be at least 0.90 m wide for up to 5 persons, 1.00 m for up to 20 persons and 1.20 m for up to 200 persons. Aisles to personally assigned workplaces may be 0.60 m wide.
- Keeping clear: the required minimum width must be kept clear at all times. Pallets, boxes and trolleys left standing are therefore a defect, not a cosmetic flaw.
- Lighting: traffic routes must be lit for the duration of use so that they can be used safely.
- Carrying on stairs: one hand should stay free for the handrail, and the item carried must not block the view of the steps.
- Weather: the employer defines protective measures against soiling, black ice and vegetation, such as cleaning methods, winter maintenance or roofing. Outdoor traffic routes are cleaned and gritted where the weather creates slipping hazards.
- Maintenance: traffic routes are checked at regular intervals and repaired where necessary; type, scope and intervals follow from the risk assessment.
Measures following the TOP principle
Technical measures work regardless of behaviour and therefore take priority. Organisational measures maintain the safe condition. Personal measures supplement both but do not replace them.
Technical
MeasuresFloor covering with the right R group, remove or bevel thresholds and edges, floor ducts and additional sockets instead of cables in the way, roofing and entrance matting at entrances, drains with a gradient, handrails and marked step edges, sufficient lighting
Organisational
MeasuresCleaning plan with suitable agents and times, wipe up spilled liquids immediately, keep traffic routes clear, fixed set-down areas, winter maintenance, regular inspections, simple defect reporting, mark and cordon off damaged spots until repaired
Personal
MeasuresSuitable footwear, instruction on handrails, carrying loads and distraction on routes, shoe spikes in winter where needed
With footwear, the sole, fit and condition matter. If the risk assessment shows that safety or occupational footwear is necessary, the employer provides it as personal protective equipment. For footwear under the standards from 2022, such as DIN EN ISO 20345, slip resistance on ceramic tiles with a detergent solution is a basic requirement; the marking “SR” stands for an additional test with glycerine that has been passed. Older footwear still carries the markings SRA, SRB or SRC. Worn-down tread is a reason for replacement.
Checklist for the inspection
- Floors level and undamaged: no holes, loose tiles, protruding edges or height differences of more than 4 mm
- Floor covering suits the use, required R group for wet and greasy areas defined and met
- Mats and entrance matting lie flat, are secured against shifting and are clean
- Cables and hoses do not lie in traffic routes, covers and gratings are flush and firm
- Traffic routes, stairs and emergency exits free of stored material
- Stairs with handrail, steps undamaged, slip-resistant and clearly recognisable
- Lighting in corridors, on stairs, in storage areas and outdoors sufficient, no defective luminaires
- Cleaning plan in place, cleaning agents suit the covering, warning signs used during wet cleaning
- Spills are removed immediately, absorbent and cleaning equipment are to hand
- Winter maintenance organised for paths, stairs, ramps and car parks
- Footwear for the activity defined and in good condition
- Defects from the last inspection remedied, slips, trips, falls and near misses evaluated
Frequently asked questions
When does an edge count as a tripping hazard?
Under ASR A1.5, height differences of more than 4 mm already count as a tripping hazard under level conditions in rooms, as do gaps more than 20 mm wide. Height differences of up to 2 cm can be bevelled at no more than 25°; larger ones should be bridged by walkable ramps.
Which slip resistance does a floor need?
That depends on the work area. Annex 2 of ASR A1.5 assigns an R group to areas in which slip-promoting substances get onto the floor: for example R 9 for indoor entrance areas and break rooms, R 10 for changing rooms and washrooms, R 11 for motor vehicle workshops and R 12 for restaurant kitchens. Particular activities may require a higher R group.
From how many steps does a staircase need a handrail?
Under the current ASR A1.8, every staircase must have a handrail, on both sides where the step width is more than 1.5 m. For workplaces built or applied for by 30 June 2013, the following applies until a substantial conversion: at least one handrail on stairs with more than 4 steps, unless the building regulations of the federal states require a handrail for fewer steps.
Does the employer have to provide slip-resistant shoes?
If the risk assessment shows that foot protection with a slip-resistant sole is necessary, it is personal protective equipment. The employer then provides the footwear and bears the cost (Section 3 (3) ArbSchG, Section 2 of the PPE Use Ordinance). However, measures on the floor itself take priority.
Does a fall at work have to be reported?
Every injury belongs in the first-aid log (Verbandbuch). If the fall leads to more than three days of incapacity for work or to death, the employer must report the accident to the accident insurance institution within three days (Section 193 SGB VII). Regardless of this, it is worth evaluating falls without consequences as near misses too.
This guide gives a general overview of German occupational safety law and does not replace legal advice. The regulations in force and the rules of the statutory accident insurance institutions are authoritative.
Organise occupational safety digitally
With the occupational safety software AMS Go you handle risk assessments, safety instructions, inspections and more in one system – mobile and with AI support.
Newsletter
Occupational safety, straight to your inbox
New templates, guides and changes to regulations – free from AMS Go. The newsletter is in German. You can unsubscribe at any time via the link in every email.
More guides
- Safety inspections
Conducting safety inspections: process, checklist and report
7 minRead - Basics
German Workplace Ordinance: duties and technical rules (ASR) at a glance
7 minRead - Health
Cold at work in Germany: minimum temperatures, outdoor work and winter maintenance
9 minRead - Health
Room temperature, ventilation and lighting in Germany: what ASR A3.5, A3.6 and A3.4 require
9 minRead - First aid & emergencies
Reporting near misses in Germany: process, duties and reporting culture
7 minRead - Protective measures
Personal protective equipment (PPE): duties, selection and instruction
8 minRead




